Stainless Steel Electrode Classification

• Welding Electrodes For Stainless Steel
• Stainless Steel Electrodes E70

1. Stainless steels are commonly grouped into martensitic stainless steels, ferritic stainless steels, austenitic stainless steels, duplex (ferritic-austenitic) stainless steels, and precipitation-hardening stainless steels Sorry to see that you are blocking ads on The Engineering ToolBox!
2. The prefix 'E' designates an arc welding electrode. The first two digits of a 4-digit number and the first three digits of 5-digit number indicate minimum tensile strength. For example, E6010 is a 60,000 psi tensile strength electrode while E10018 designates a 100,000 psi tensile strength electrode. The next to last digit indicates position.
3. Since these electrodes require special chemical formulations, they must be ordered on a special request basis from most manufacturers. 5.7 MARTENSITIC STAINLESS STEEL Martensitic stainless steels fall into the 400 number series according to the American Iron and Steel Institute. They are magnetic and contain from 11.5% to 18% chromium.

GMAW (MIG welding) electrodes are designated by some letters and numbers such as ER70S-6, ER90S-6 and E308L etc. I will explain the meaning of these symbols:

Stick Electrode Classification Stick electrodes are sold for the following metals:. mild steel. stainless steel. low-alloy steel. cast iron. aluminum AWS classifies stick electrodes according to several codes, depending on the metal type. One of the most common is AWS A5.1/A5.1M: Specification for Carbon Steel Electrodes for. Stainless Steel Grades: 309 Stainless and Welding Carbon Steel to Stainless Steel or Low Alloy Steels. AWS Electrode Classification: ER309L; Shielding Gas: C2 or 2% Carbon Dioxide and 98% Argon; Stainless Steel Grades: 304,305, 308, 310, 312, 314, 316, 317, 321, 347 and 348. AWS Electrode Classification: ER316L and ER316LSi; Shielding Gas: C2.

FOR CARBON STEEL OR MILD STEEL (SUCH AS ER70S-6 OR ER70S-3)

Where,

ER – Designates electrode or filler rod

XX – Designates the minimum tensile strength of the deposited weld metal

S – Stands for solid wire

Y – Designates the chemical composition of the additives such as deoxidizing agent or cleansing agent used on the electrode, it may affect the polarity setting also.

FOR EXAMPLE:

ER70S-6

Where,

ER – Designates a welding electrode or filler wire

70 – Designates the minimum tensile strength of the deposited weld metal shall be 70 Ksi or 70,000 Psi

S – Stands for solid wire

6 – Reflects the amount of oxidizing agent and cleansing agent on the electrode. In particular the number 6 means that more deoxidizers have been added to the wire, which is helpful when welding on dirty or rusty steel.

FOR STAINLESS STEEL

Stainless steel electrodes are designated in a slight different way. Some of the commonly used stainless steel electrodes are ER308L and ER309L etc. Meaning of these symbols is explained below;

ER308L

Where;

ER – Stands for electrode or filler wire

308 – Designates the grade of stainless steel of the electrode or filler wire

L – Designates that it is a low carbon electrode

FOR ALUMINIUM

For Aluminum, electrodes are designated as ER4043, ER5350 etc. These electrodes are designated in a different way. For example;

ER4043

Where,

ER – Stands for electrode or filler wire

Welding Electrodes For Stainless Steel

4 – Designates series of Aluminum of which the electrode is made from. In this case it's a 4000 series Aluminum

043 – Reflects the amount of silicone added to the electrode

SHIELDING GAS:

GMAW requires a shielding gas, to protect the weld pool from atmospheric contamination. Following gases are used as shielding gas;

• Argon
• Carbon Dioxide
• Helium

(NOTE: Whenever Carbon dioxide is used as shielding gas in Gas Metal Arc Welding (GMAW). The term MAG (Metal Actve Gas) welding is used, because Carbon dioxide is an active gas. Whereas, other shielding gases such as Argon and Helium are inert in nature. Hence, whenever theses gases are used as shielding gas, the term MIG (Metal Inert Gas) welding is used.)

These gases are used alone or a combination of gases can also be used. Commonly used combinations of inert gases are;

• 75% Argon + 25% Carbon Dioxide (most popular combination)
• 98% Argon + 2% Carbon Dioxide

Argon helps in achieving cleaner weld whereas, Carbon dioxide helps in getting a deeper penetration. Carbon dioxide can be used alone also and it is effective while welding thinner metals.

Relationship between filler wire diameter, current range and wire feed speed:

In MIG/MAG welding, Voltage, Current and wire feed speed must be controlled for sound welding

The Voltage controls the weld profile. Whereas, the Current controls the heat input, size of weld and the depth of penetration.

Stainless Steel Electrodes E70

The following table (Table – 1) gives the current range and the filler wire feed speed, based on the filler wire diameter. This table is just a guide and the ranges may vary depending upon the shielding gas and parent metal.

Table – 1